- 1 Pictures
- 2 Hardware Information
- 3 User Guide
- 4 Firmware
- 5 How to Compile Your Own WR703N Firmware for Avalon
- 6 IRC: ##avalon @freenode.net
- 7 FAQ
- 8 Links
Technology Summary: TSMC 0.11- micron G process 5 Metal Core Voltage: 1.2 V I/O Voltage: 3.3 V Core Frequency: 256+ MHz Number of Pads: 48 8 Data 40+1 Power Package Type: QFN48 -0.5 Pitch Packaged Chip Size: 7 mm x 7 mm Chip Interface Data Pins (8 in total): Clock i Serial Data In  i Serial Data Out  o Serial Data Bypass  o Reserved  -
TSMC TMEM91 Chip Size : X = 3.9760 ,Y = 4.0560 mm Reticle Size : X/cell = 3 ,Y/cell = 3 Offset Value : X = -3.7668 ,Y = -2.2990 mm Alignment Mark : (118.80,83.20),(-118.80,-83.20) Alignment Mark Tolerant Distance : 1.6 mm Notch Reserved Distance : 7.75 mm Start Distance : 7.75 mm Ring Edge : 3.0 mm Photo Die Number: 4055
Chip power efficienty: 6.6W/GHs @ 1.15 V Module power consumption: 149W @ 20GHs/ 164W@ 22GHs Machine power consumption: 595W @ 220V-AC/ 620W @ 120V-AC
- Connect your laptop to the eithernet port of the Avalon
- Setup your laptop IP address 192.168.0.101
- Open http://192.168.0.100
- Make sure WR703N can access Internet, Configure WiFi: Network -> WIFI -> Scan(select your WIFI network) -> Join Network -> WPA passphrase -> Submit -> Save & Apply for connect to WIFI Internet
- setup your mining worker: Status -> Cgminer Configuration.
- Restart the cgminer service: System -> Startup,
- Check your avalon status: Status -> Cgminer Status
- Setup password/using ssh
ssh email@example.com # Once you setup the password the telnet service will be stop. use ssh instead.
--avalon-options 115200:24:10:45:282. this is the default avalon option. here is the details:
115200: the serial baud. this have to match the controller baud. 24: the miner count.(there are 3 modulars in avalon. each modular have 8 miners), if your avalon have 4 modulars. change it to 32 10: the chip count pre miner. 45: the controller timeout parameter. the valid number: 50, 47, 45, 40. 282: the chip clock. the valid number: 256, 270, 282, 300.
Run cgminer manually
In case you need to run Cgminer in linux console please run the following command:
- Stop/start Cgminer:
# /etc/init.d/cgminer stop # /etc/init.d/cgminer start
If your avalon does not mine properly, please run Cgminer in debug mode with -D --verbose option. For example:
# cgminer -S /dev/ttyUSB0 -o stratum.btcguild.com:3333 -O xxxx:yyyy -D --verbose --avalon-options 115200:24:10:45:282 --api-allow "W:0/0" --api-listen 2>/tmp/cgminer-debug.log
There is a modify version of TP-LINK TP-WR703N inside Avalon. cgminer running at 703n, this 703n have 64MB ram and modified power supply. it power from the usb-client side(we moved a 0R resistor from J1 to R113 for that)
Why there is a ugly USB HUB there? because some compatibility problems come out if you connect the 703N to the controller board directly. add a HUB can 99.999% solve this problem.
After review this issue, i think maybe one or two HUB ports damaged during the delivery. just change to another USB port and try please.
- Latest Avalon images is here.
System -> Backup / Flash Firmware -> Flash new firmware image (make sure Keep settings is checked)
Attention: To avoid your WR703N become a brick, during flash your WR703N be careful DO NOT power off avalon, and DO NOT break your network connection. Just wait there till you see OpenWrt login web page again.
Attention: If not essential please do not re-Flash your Avalon. Because not all of WR703N issue could be resolved by reset button. If you want to play WR703N I would like to recommend you order a standalone TP-LINK WR703N from ebay or somewhere for studying purpose.
WIFI or Ethernet Cable ?
Avalon shipped with a 9db antenna after connect it to WR703N usually could establish good wireless connection with your WIFI router. But if for some reason you would like to use Ethernet Cable to connect Avalon with your network, please login OpenWrt and configure the LAN port:
Network -> Interfaces -> LAN -> Edit -> Common Configuration -> General Setup
Attention: You need to configure it correctly based on your own network enviroment. If anything wrong you might could not access your WR703N any more.
Start to mine
To maximize your Avalon miner's performance, it is recommended that you choose pools with the stratum protocol supported. The default mining pool configured in Avalon is ozco.in. To change it login to OpenWrt:
Status -> Cgminer Configuration
Click "Save & Apply" to save your update. To make it take effect immediately you need to restart the cgminer
System -> Startup -> cgminer # click Restart.
To get more information about how to configure specific pools, please check their website. If you run multiple Avalons, we recommend that you create a dedicated worker for each of them. This will make it easier to monitor your Avalons through the pool's website and identify possible problems.
About P5 jumper: close this jumper will supply 5V to the USB-B port. in this system, the controller board power the HUB and the HUB power the 703N. but if you connect the controller itself to a PC, you must remove the jumper.
P2Pool Operation with Avalon
There is an /avalon branch Forrest committed to the p2pool github repository. Make sure that is checked out.
Next, include the option:
--fix-protocol: Do not redirect to a different getwork protocol (eg. stratum)
This will correct the Avalon's communications with P2Pool. Without this option, the default operation will spam share submissions and duplicate work to your running P2Pool instance.
- There is a pair of gloves in Avalon package. please put it on when assembling or carrying.
- About the plastic sheets: please remove them BEFORE mining. we design the case as a part of heatsink, so remove the plastic sheets is a must
- About FAN change: DO NOT change the fans to a low speed model. will cause over heat. DO NOT install extra fans at the rear "fan socket". will cause PSU over heat and nearly useless for module cooling.
- About install extra heat-sinks on each avalon chip: please do not do that. there is a air gap between the die and package top, install a heatsink on chip is useless. and will cause overheating. because the top PCB copper act as a heatsink too. do not cover them.
- About water cooling: yes, do it.
- Latest Firmware is here
- Check your firmware version. ssh/telnet to your Avalon run
- The Avalon Firmware SDK is here
- Reset then Idle avalon before close it.
- Only record matched result (Should fix the temp/fan jumping issue)
- Fix no_matching_work only count in debug mode
- Update cgminer-monitor, fix [Accept] give null at the first few seconds of cgminer start
If you "check the Keep settings", you need fill API Allow to "W:127.0.0.1" after reflash, edit it here: "http://AVALON_IP/cgi-bin/luci/admin/status/cgminer/", "DO NOT" left it blank
If you "uncheck the Keep settings" when reflashing, Please "reconfigure your Avalon" after reflash
- Update Linux from 3.6 to 3.8.3
- Update OpenWrt to r36095
- When there is no network. automatic idle chip after detect avalon, save power and protect your avalon overheat
- Idle chip when cgminer close avalon
- Add device_reinit support
- Add frequency, modular configure on web ui
- Add API Allow on web ui
- Add pool balance on web ui, by default balance on all 3 pools
- Add stratum+tcp:// by default
- Display Frequency on status page
- Fix the kern.err kernel: ... ath: phy0: ... bug
- Fliter >=100 degree result for debug
- Replace TempMax with No Matching Work
- A new cgminer status page
- /etc/avalon_version include all repo commit
- Fix temp_history_count, make sure 2~3s call adjuest_fan
- Update adjust_fan()
- Using avaon default worker
- Update fan pwm
- Update fan pwm MAX/MIN
- Sync with upstream, fix the memory leak bug
- Monitor the Accept number
- Add overclock code
- Change the cgminer configure to UCI system
- Add the simple web ui
- Update OpenWRt to r35097
- Update cgminer to 2.10.4
- Remove /www/miner.php, change cgminer cron job to */5
- Start ntpd before start cgminer
- New firmware don't break Avalon for sure
- New firmware don't use all flash. have to keep some space for save configuration
- Either and WiFI connect works fine
- Cgminer works fine(the kernel user driver, cgminer it self, cgminer-monitor and uci configurations files)
- After configure cgminer. [Save & Apply] can restart the cgminer
- The Status/API log page works fine
- Test mining
- Make sure 80/22/4028 open on WAN.
How to Compile Your Own WR703N Firmware for Avalon
1. First check if you have met the building prerequisites. Checkout this page first OpenWrt Buildroot – Installation
For example, if your OS is Ubuntu 12.04 LTS, install the required packages like this:
sudo apt-get update sudo apt-get install subversion build-essential sudo apt-get install build-essential subversion git-core libncurses5-dev zlib1g-dev gawk flex quilt libssl-dev xsltproc libxml-parser-perl
2. Now get the source code.
mkdir avalon cd avalon svn co svn://svn.openwrt.org/openwrt/trunk@35097 openwrt git clone https://github.com/BitSyncom/cgminer-openwrt-packages.git git clone https://github.com/BitSyncom/luci.git git clone https://github.com/BitSyncom/cgminer.git cgminer-20130108
3. Prepare the code and build.
cp -R cgminer-openwrt-packages/cgminer openwrt/package tar -zcvf cgminer-20130108-HEAD.tar.gz cgminer-20130108 python -m SimpleHTTPServer& cd openwrt ln -s package/cgminer/root-files files ln -s package/cgminer/data/feeds.conf cp package/cgminer/data/config .config sed -i 's/ck.kolivas.org\/apps\/cgminer\//localhost:8000\//g' openwrt/package/cgminer/Makefile ./scripts/feeds update -a && ./scripts/feeds install -a cp package/cgminer/data/config .config #overwrite again make -j4 cd ../luci git checkout cgminer-webui cp -R applications/luci-cgminer ../openwrt/build_dir/target-mips_r2_uClibc-0.9.33.2/luci-trunk+svn9679/applications/ cd ../openwrt make -j4
4. Finally you could get the freshly built firmware files under openwrt/bin/ar71xx/
IRC: ##avalon @freenode.net
##avalon @freenode.net Thanks to midnightmagic create that channel
- Why ASIC bitcoin mining?
- Why Avalon?
- Who made Avalon?
- How to order one?